PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 206

Страница: 206 / 284

206 . Clarus 590 GC User’s Guide

If you press

, the Save As… dialog box displays the same fully populated list of methods.

The new method name is still in the Name field. You can press

Cancel

to return to Method Edit

mode and access the File button, or

to prompt the memory full error again.

Activate

This command is deactivated while the system is running. When the command is available, the Activate

option applies the currently edited method conditions and name to the active method. The method editor

mode retains control. If the method is not named, the Save As dialog box opens for you to select a

method from the list.

Delete

Touching the delete option prompts the

Delete

dialog box.



Select a name from the list. The selected name appears in the Method Name field. Touch the

button to delete the selected method and close the dialog box.

Exit Editor

The Exit Editor option closes the Method Edit screens and restores the Active Method. Touching Exit

Editor invokes the following dialog box:



Pressing the

Yes

button closes the dialog box and displays the active method screens.



Pressing the

button closes the dialog box and retains the Method Editor mode.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды