PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 203

Страница: 203 / 284

Managing Methods . 203

To save it, touch

or touch

Cancel

to close the Save As dialog box When the dialog box

closes, the GC is in the New Method mode and the fields are populated with default values. The

Method Name field is activated and displays the name “untitled.”

After defining the values for the new method, touch the Method Name field to display the Save

As dialog box. Assign a name to the new method and save the changes.

Open Method

Touching the Open Method option prompts the following warning box indicating that the current

method is not saved.

If you touch

Yes

, the Save As.. dialog appears.

When the Open option is selected, the Open dialog appears for you to select a method.

Touch the

method name

and

to populate the method edit screens with the values from the

selected method.

If you choose

Cancel

, or touch the

button without selecting a method, the dialog box will

close and the operation will be ignored.

Save

The Save command saves the previously opened and optionally modified method under the same name.

No dialog box appears if a name appears in the Method Name field.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Бренды по названию

Популярные бренды