PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 17

Страница: 17 / 284

Glossary of Clarus GC Terms . 17

Glossary of Clarus GC Terms

The glossary of Clarus GC terms are divided into two types:

•

Autosampler Terms

•

Instrument-Specific Terms

Autosampler Terms

Term

Description

Washes

Washing the syringe.

Pre

The number of prewashes of sample to prime the

syringe (no pumping).

Post

The number of post injection syringe washes with a

solvent.

Pumps

The number of times the syringe draws up sample and

evacuates it before acquiring the volume. This is done

to eliminate bubbles.

Mode

The style of injection.

Fast

Fast speed of the syringe during sample injection. This

is used to eliminate discrimination in the needle.

Normal

Normal speed of the syringe during sample injection.

Slow

Slow speed of the syringe during sample injection in

order to inject directly into a wide-bore capillary column,

in hot injection port.

Instrument-Specific Terms

Term

Description

Background

compensation

A routine that automatically subtracts a stored

calibrated baseline profile from the signal generated

during a GC run.

Ballistically

Changing the oven temperature as quickly as possible

to reach a set point.

Detector

background

The detector output signal when no components are

being eluted.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды