PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 205

Страница: 205 / 284

Managing Methods . 205

•

Touching

Cancel

closes the keypad and displays the Save As screen. The name field is not

modified.

The

External

method is always the last entry in the list. The External method cannot be

renamed but it may be overwritten.

•

Touching

saves the edited method under the assigned name. The name is added to the

list and the Save As box closes. The new name appears in the Method Name field.

•

If you press the

button before entering a method name, the following error message

appears:

Pressing

Continue

returns control to the previous screen. You can select a name or cancel out

of the process.

If five methods are already stored, entering a new name will prompt the following dialog box:

If you press

Yes

, the method list appears.

When you select a method and press

, the Save As screen appears with the new method

name in the field. You can now press

to save the method in the available position.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Бренды по названию

Популярные бренды