PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 146 | Manualshive

Страница: 146 / 284

PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 146

146 . Clarus 590 GC User’s Guide

Set the Make-Up Gas in the PPC Version

CAUTION

ATTENTION

The PID flow module for reference gas is calibrated with helium

gas at the factory. You must recalibrate the PID flow module if

you are using a reference gas other than helium.
Le module de débit PID pour le gaz de référence est étalonné avec

de l'hélium gaz en usine. Vous devez recalibrer le module de flux

PID si vous utilisez un gaz de référence autre que l'hélium.

1.

With PPC pneumatics the make-up gas is set from the Clarus GC touch screen.
The PPC modules are calibrated at the factory: therefore, to set the flows for an analysis, simply

follow this procedure.

2.

To set the make-up and reference gases touch the

button in PID tab screen

then touch

Configuration

from the drop down menu. This will bring you to the

PID Configuration screen page (see screens above).

3.

In the PID Configuration screen set the make-up gas and reference gas line
pressures to 60 - 90 psig by using the up and down arrow or keypad

buttons.

4.

As shown in the example above use the up and down arrow or keypad

buttons to set the filter to 200 and the output to 5.When all the settings are

appropriate for your analysis touch

OK

. The TCD tab screen will be now visible and the changes

you made in the configuration screen will be shown.
The default setting for the filter is 200 milliseconds. If you want to improve the signal-to-noise,

change the setting to 800 milliseconds; however, the noise improves but the peak shapes broaden.

If you want a faster detector response, change the setting to 50 milliseconds; however, the noise

level may increase.

Adjust the Make-Up Gas in the Manual Pneumatics Version

To adjust the make-up gas in the manual pneumatics version use the on/off needle valve mounted on the

pneumatics control panel.

NOTE: Do not overtighten the inner flow adjustment screw in the on/off needle valve. Overtightening damages

the mechanical device.

The manual pneumatics make-up gas control valve is shown below.

The make-up gas control valve consists of an outer ring (used to turn the make-up gas completely off or

on), a protective cap, and an inner needle valve (used to adjust the flow of make-up gas). Removing the

«
...
144
145
146
147
148
...
»

Содержание CLARUS 590 GC





























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды