PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 284

background image

FID Overview . 117

The PPC version of the FIDW has

flameout

detection and an

auto-ignite

feature. Flameout detection

occurs 0.5 minutes into the PRE-RUN time and it measures the user-entered baseline threshold level in mV.

If the threshold level is exceeded, the flame is considered lit, otherwise the Clarus GC detects that the

flame is out and auto-ignite automatically lights the flame before the start of a run.
With the FIDW temperature set, the air and hydrogen flows set, and auto-ignition activated by setting a

positive mV value for the flame offset, the FIDW attempts auto-ignition at -0.5 min. before the system

becomes ready. At this Pre-run time the status bar flashes “

Flame Ignition”

as the air flow is shut off,

hydrogen purges the FIDW for about 10 seconds, and the ignitor energizes for ignition followed by a return

of the air flow to the detector to sustain the flame.
After the flame ignites, the FIDW output level is monitored to confirm ignition before producing a READY

signal. If ignition is not confirmed, the ignition process repeats up to two more times if needed. If ignition

is not achieved after three attempts, the flame gases are set to off and a dialog box appears displays the

following message:

“

Flame 1 or 2 failed to ignite.”

Touch the OK button. The status is made NOT READY and “

FID 1 or 2 flameout”

appears. If auto-

ignition is attempted with the FIDW gases set to zero flow, the message “

No ignition. Flame gases are

off”

appears on the screen. To proceed, go to the Configuration screen and reset the air and hydrogen to

their 450 and 30 mL/min flowrates.

To Auto-Ignite

The auto-ignition process only occurs before the start of each run just prior to the instrument becoming

READY. However, the manual flame ignition process can be initiated at any time by touching the

Ignite

button

.

1.

When auto-ignite begins the Clarus GC equilibrates.

2.

Once the two minutes of equilibration expire,

Pre-run

begins and the GC detects that the flame is

not lit and indicates this by alternately flashing

Flame

and the

method name

in the status bar.

3.

After determining that the flame is not lit, the GC switches to a not ready state and attempts to

automatically ignite the flame.

Flame Ignition 1

appears in the status bar.

4.

The air flow is shut-off and hydrogen is purged through the FID for

10 seconds.

5.

The ignitor energizes, the flame ignites (indicated by the POP), and air flow is returned to sustain

the flame. The FID output level is monitored to confirm that the flame is lit. If a lighted flame is

not confirmed, the Clarus GC repeats the ignition process up to two more times.

Manually Ignite the Flame

You can manually ignite the flame at any time by following this procedure. Before trying to ignite the

flame, make sure that you have sufficient combustion gases and they are turned on at the source, and

make sure that the flows are set as described earlier in this section.

«
...
115
116
117
118
119
...
»

Содержание CLARUS 590 GC





























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CLARUS 590 GC

Бренд: DARAY Страницы: 24

Бренд: Jafar Страницы: 9

Бренд: HAMAR LASER Страницы: 49

Бренд: Velocitek Страницы: 81

ABS-Lock X-Flat

Бренд: ABS Страницы: 8

ABS-Lock X-DURCH

Бренд: ABS Страницы: 8

Бренд: ABS Страницы: 8

Бренд: Eaton Страницы: 16

Бренд: Eaton Страницы: 6

Бренд: Ecco Страницы: 17

Бренд: Haaga Страницы: 31

Бренд: VBM Страницы: 36

Бренд: W&H Med Страницы: 122

Бренд: IDS Страницы: 2

Бренд: Nautilus Страницы: 17

Бренд: National Instruments Страницы: 6

Бренд: Palmer Страницы: 2

Бренд: Safavieh Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды