PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 284

background image

108 . Clarus 590 GC User’s Guide

Wash vials

Program 1

splits between solvent wash vials #1 and #2. For example, if four washes are required, two

will be taken from vial #1, and two will be taken from vial #2.

Program 2

splits between solvent wash vials #3 and #4. For example, if five washes are required, three

will be taken from vial #3, and two will be taken from vial #4.

About Sample Vials

Use 2-mL vials with the autosampler (P/N N9301385, 144 per box). These are crimp-top vials. The vials

and crimp caps with septa (P/N 00092205, 1000 per box) are available through PerkinElmer’s Consumables

and Supplies catalog (in the U.S., call: 1-800-762-4000) or online at

www.perkinelmer.com

.

The minimum volume of sample required in the 2-mL vial is 0.35 mL or 350

µ

L. You should fill the vial

when running multiple injections per vial.
A mini-vial insert is available for laboratories with small sample volume requirements. This insert fits into

the standard 2-mL vial and requires a minimum volume of 5

µ

L of sample. These inserts are available

through the Consumables and Supplies catalog or visit us on-line at

www.perkinelmer.com

.

NOTE: When using mini-vials, it is not recommended to use pumps to acquire samples. This assures that the

sample will not be diluted by residual solvent in the syringe.

Only PerkinElmer vials should be used with the Clarus GC.

Adjust the crimper so that it does not deform the vial cap and septum, but crimps the vial cap tight enough

so that you cannot turn the cap. An improper adjusted crimper can cause the autosampler to malfunction.

Using a TCD w ith the Autosampler

When using a TCD at high sensitivity with a GSV or the autosampler, a minor baseline upset may occur at

the time of injection.
If the signal goes below zero, incorporate a timed event Autozero to bring the signal back to zero before

the peaks of interest elute.
Observe the initial chromatogram to determine the proper time for the timed event.

Available syringes

The following syringes are available for the Clarus GC:

Syringe

Part Number

5-µL (0.63 mm O.D.) Teflon-tipped plunger (Std)

N6101390

0.5-µL (0.63 mm O.D.)

N6101252

0.5-µL (0.47 mm O.D.)

N6101253

5-µL (0.63 mm O.D.)

N6101251

5-µL (0.47 mm O.D.)

N6101380

50-µL (0.63 mm O.D.)

N6101760

NOTE: A 0.47-mm needle is required for use with the POC injector and 530-

µ

m columns in the on-column injection

mode only. You can achieve better precision in the on-column injection mode when you use sample

volumes of 1.0

µ

L or greater.

«
...
106
107
108
109
110
...
»

Содержание CLARUS 590 GC





























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CLARUS 590 GC

Бренд: Tanco Страницы: 72

Бренд: HABYS Страницы: 16

Бренд: Acterna Страницы: 72

Sportsound SSR-300

Бренд: Daktronics Страницы: 42

Crouse-hinds series

Бренд: Eaton Страницы: 32

Growers Supply 109722

Бренд: FarmTek Страницы: 9

Бренд: Velp Scientifica Страницы: 12

Бренд: Yamaha Страницы: 24

Бренд: J&M Страницы: 33

Бренд: Velleman Страницы: 16

Бренд: Velleman Страницы: 11

Бренд: Yamaha Страницы: 126

DM 2000 Version 2

Бренд: Yamaha Страницы: 8

Бренд: RainPoint Страницы: 40

Бренд: FARM-MAXX Страницы: 35

Бренд: yellow jacket Страницы: 8

Бренд: SIP Страницы: 16

ZoneVu ZVD-GW1-STR

Бренд: ZoneVu Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды