PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 54

Страница: 54 / 284

54 . Clarus 590 GC User’s Guide

Timed Events

Events Tab

The

Events

tab accesses the timed events table, buttons, valves (relays), and Aux gas controls.

Screen Element

Enabling

Timed events table

Always

Aux gas button

PPC configuration

Relays button

Always (see below for details)

Add button

Always

Edit button

Always

Delete button

Always

Clear button

Always

Timed Events Table

The timed events table displays the time, name, and value of each event. Timed events may be added and

removed while the GC is running. The next event to be executed is automatically selected. Up to 32 events

can be specified. The configured hardware determines which events are available. Events that are not

applicable should not be available. The following table lists the available events.
The time range is -99 to 999 minutes. Events occurring after the temperature program is complete are

ignored.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды