PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 167

Страница: 167 / 284

FPD Overview . 167

Use the up and down arrow or keypad

buttons

to e nte r a se tpoint of a t le a st 250 C

(this is the minimum entry for a FPD) in the temp field

, or enter a temperature that is

C higher than the highest temperature of your oven program.

Set the Hydrogen Flow and Air Flow for PPC

The PPC pneumatics consists of PPC modules where the hydrogen and air gases are set from the Clarus GC

touch screen.
The PPC modules are calibrated at the factory, therefore to set the flows for an analysis, simply follow this

procedure.

Turn on the air at the source and adjust the pressure to 70 - 90 psig.

Turn on the hydrogen at the source and adjust the pressure to 60 - 90 psig.

From the System Status screen touch the FPD icon.

The FPD tab page is now visible.

To change the gas flow values touch the

button in FPD tab screen then touch

Configuration

from the drop down menu.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды