PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 102

Страница: 102 / 284

102 . Clarus 590 GC User’s Guide

The Autosampler screen includes three tabs. The first two tabs display identical screens for setting

Program 1 and 2, allowing you to sequence two methods. The Tasks tab displays buttons to

perform tasks such as Park, Clean, and specify a priority injection. All of the screens provide status

information.
The method field allows the user to run the GC under the control of a method other than the

current active method.

Start Button

Touch the

Start

button to start a run. The Start button is active whether or not the system is ready.

Issuing the start command before the system is ready gives users the flexibility to set up and run a method

without having to wait for the system to attain ready status. As soon as you touch

, the Start button

changes to

Stop

whether or not the system is ready. This enables you to cancel the run before it starts.

•

If the system is under external control (e.g. from TotalChrom) and a method has not yet been set up,

the Start Button is inactive.

•

In all other instances, even though the GC is not Ready, the Start Button will start a run.

•

When the GC oven starts to program, the Start Out signal will be asserted for 1 second.

•

The Ready Out signal will be asserted only when the GC is fully equilibrated and the GC has reached

full Ready status.

Stop Button

As soon as the

Start

button is touched, the

Stop

button appears on all top level screens.

Touching the Stop button before the system is running prompts the following dialog box:

Touch

to cancel the run.

The status bar reflects that the system is running and the Start button changes to Stop.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды