manualshive.com logo in svg

PerkinElmer CLARUS 590 GC, Руководство пользователя

Поделиться
Скачать
PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 122

122 . Clarus 590 GC User’s Guide

 

 

 

Each pneumatic control consists of an outer knob (which is used to turn the hydrogen or air completely on 

or off), a cap, and an inner gas flow adjustment screw. 
Removing the cap exposes the gas flow adjustment screw.  To set the air, flow use a small thin screwdriver 

(P/N 09907273, supplied in the shipping kit) to turn the adjustment screw.  Turn the screwdriver 

counterclockwise to increase the flow or clockwise to decrease the flow.  To set the hydrogen, use a hex 

wrench (P/N 09907235, supplied in the shipping kit) to turn the adjustment screw.  Turn the hex wrench 

clockwise to increase the flow or counterclockwise to decrease the flow.  
To adjust the hydrogen flow: 

1.

 

Turn the air off by turning the outer ring of the air control valve completely clockwise. 

2.

 

Turn on the hydrogen at the tank.  Adjust the line pressure to 30 psig. 

3.

 

Start the hydrogen flowing by turning the outer ring of the hydrogen pressure regulator completely 

counterclockwise (see the previous figure). 

NOTE:  The outer knob is the on/off knob and it must be turned fully on for complete flow.  In the case of the 

pressure regulator, if this knob is only partially opened, the flow will be less than the setting made when 

the knob was fully opened. 

4.

 

To access the adjustment screw, remove the protective cap from the hydrogen pressure regulator. 

5.

 

Insert the hex wrench (P/N 09907235) in the adjustment screw and turn it clockwise a few turns. 
For safety reasons, the hydrogen pressure regulator is set to a very low flow before it is shipped 

from the factory. 

6.

 

From the System Status window touch 

Tools

. From the Tools drop down menu touch 

Utilities

. 

Содержание CLARUS 590 GC





























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды