PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 118

Страница: 118 / 284

118 . Clarus 590 GC User’s Guide

CAUTION

ATTENTION

To ensure proper auto-ignite FID operation, make sure your

column is positioned in the FID 3.74 inches (95 mm) from the

back of the column nut.
Flame ignition may not occur if your carrier gas flow is 60

mL/min or higher.
Pour assurer un fonctionnement correct de l'auto-inflammation

FID, assurez-vous que votre colonne est positionnée dans le

FID à 2,74 pouces (95 mm) à l'arrière de l'écrou de la colonne.
La flamme peut ne pas s'allumer automatiquement si le débit

de votre gaz porteur est de 60 mL / min ou plus.

Touch the

FID (FIDW)

icon from the System Status screen.

The FID tab page appears:

NOTE: For proper ignition to occur, the FID must be heated to at least 100

Touch the temp field

and use the up and down arrow or keypad

buttons to enter a setpoint of at least 100

C, or enter a value 50

C higher than the highest

temperature of your oven program.

Wait for the FID temperature to become READY. When the temperature is ready a green light
appears next to the temperature display

Touch the

Ignite

button

(Note the signal level in mV before the flame ignites.)

Upon pressing the Ignite button, the air flow turns off for 15 seconds,

Flame Ignition 1

appears

in the status bar, and the glow plug begins to glow.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды