PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 47

Страница: 47 / 284

Detectors . 47

Configuration Settings

The following graphic shows the

Configuration Screen

with the settings that appear on the

Active

Method Screen

Active Method

Configuration Screen

Manual Pneumatics

The manual pneumatics version of the FID shares several common elements with the PPC version. The

only difference is that the gas flow settings do not appear on the screen. The Auto-Ignite feature is not

available with manual pneumatics.

TCD

The Thermal Conductivity Detector (TCD) is a dual-channel detector which measures the difference in

thermal conductivity between carrier gas flowing through a reference channel and carrier gas plus sample

flowing through an analytical channel.
Four tungsten-rhenium filaments are connected in a bridge circuit, two in each channel. The TCD is set

up with the same amount of carrier gas flowing through both channels. The presence of a sample

component in the carrier gas flowing through the analytical channel changes the resistance of the

filaments in that channel. This unbalances the bridge and produces a signal proportional to the amount of

sample.
The following screens show the

Active Method

screen and the corresponding settings in the

Configuration

screen.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Бренды по названию

Популярные бренды