PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 155

Страница: 155 / 284

NPD Overview . 155

Adjust the Hydrogen Flow

NOTE: For safety reasons, the hydrogen pressure regulator is set in the off position (turned completely clockwise)

before it is shipped from the factory.

Turn on the hydrogen gas at the tank and adjust the line pressure to 30 psig.

Connect the tubing from a flow meter to the end of the hydrogen line at the NPD. It is marked

with a red sticker.

Turn the hydrogen pressure regulator outer knob fully counterclockwise to open it.

NOTE: The outer knob is the on/off knob and it must be turned fully on for complete flow. In the case of the

pressure regulator, if this knob is only partially opened, the flow will be less than the setting made when

the knob was fully opened.

To expose the adjustment screw, remove the protective cap from the hydrogen pressure regulator.

Insert the hex wrench in the adjustment screw and turn it clockwise to increase the flow.

From the System Status window touch

Tools

. From the Tools drop down menu touch

Utilities

In the Utilities screen touch

Stopwatch

icon.

Measure the flow rate. For best accuracy, use a soap bubble flowmeter volume that gives a reading

of at least 30 seconds.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды