PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 107

Страница: 107 / 284

Controlling the Autosampler . 107

The plunger speed during sample acquisition and injection will vary with the viscosity of the sample. To find

the optimum setting for the sample being analyzed, you should experiment with various syringe settings.

Highlighting the

Viscosity Control

Field use up and down arrow or keypad

buttons to enter

a value between 1 and 15. This value is the number of seconds the plunger pauses at the top-of-stroke

during sample acquisition.

NOTE: You can obtain improved precision with viscous samples by using the 0.5-mL syringe and septa in the

waste/wash vials in place of the diffusion caps.

Using Solvent Pre-Washes

Pre-washes refers to the number of solvent washes you want the system to perform prior to the pre-

injection sample washes. Highlight the

Solvent Pre-Wash

field and use the up and down arrow or

keypad

buttons to type in a value. Acceptable values are 0, 1 or 2. Pre-washes occur only at

the beginning of an autosampler program.

Priority Button

Press the

Priority

button to inject a priority sample during a run.

Touch the Priority Button in the

Tasks

tab.

In the Number of priority injection field use up and down arrow or keypad

buttons to

input the number of priority injections. Touch

Start

This option instructs the autosampler to interrupt the vial injection sequence and inject a "Priority"

vial that has been placed in the "Priority" position of the turntable. The priority vial will be injected

after completion of the current run.
After the priority vial has been injected (in accordance with the current program parameters), and

the priority run completed, the program continues with the next injection in sequence.

NOTE: Priority can only be selected when with the above screen is visible.

About Waste and Wash Vials

The Autosampler software has been optimized to use waste vials and solvent wash vials to minimize

contamination of the syringe needle.
Septa are available for the waste vials and solvent wash vials by ordering P/N N9302780. We recommend

using these septa in place of the diffuser caps when you are using:

•

Very viscous samples (to wipe the sample off the outside of the syringe needle).

•

Toxic solvents and samples.

•

Very volatile solvents.

Multi-Program Mode

Waste Vials

When operating in the Multi-Program Mode, the sample pre-washes are emptied into waste vial #1 for

program 1 and waste vial #3 for program 2. The solvent post-washes are emptied into waste vial #2 for

program 1 and #4 for program 2.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Бренды по названию

Популярные бренды