PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 141

Страница: 141 / 284

TCD Overview . 141

NOTE: Operating at too high a temperature can have an adverse effect on filament life.

Table 4-1. Bridge Current Range vs. Max. Detector Operating Temperature

Bridge Current Range

Recommended Operating Temperatures

for the Following Detectors

He or H

Argon

Up to 100

Do not Use 4

Up to 300

Do not Use 3

Up to 350

Up to 110

Do not Use 2

Up to 350

The correlation between bridge current and range is in Table 4-2:

Table 4-2. Correlation Between Bridge Current and Range

Bridge Current (mA)

Range Entry

Off

±0

±1

±2

120

±3

160

±4

NOTE: Entering a negative number reverses the detector polarity. For examples of reversing the polarity, see the

Clarus GC Hardware Guide, Maintenance Chapter, section “Practical Hints.”

Balance the Bridge

In the System Status Screen touch the

Signal

icon

to get to the Signal screen. This will allow

you to observe the signal as you adjust the potentiometer.

Allow the system to stabilize for about 20 min, then open the detector cover.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Бренды по названию

Популярные бренды