PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 214

Страница: 214 / 284

214 . Clarus 590 GC User’s Guide

PSS - Programmed Split/ Splitless Injector

The PSSI injector includes a

Capillary Control

option

If the

Capillary Control

mode is selected the following additional parameters are displayed

(shown below in the bordered area) and the

Capillary Control

can be configured for pressure,

flow, and velocity.
When set for inlet programming, the injector is first heated to the injector temperature entered in

the method and then follows the injector temperature program. The temp field does include a

program settings button in this case.

•

If the

Capillary Control

mode is set for flow or velocity, the radio buttons for

Program

and

Oventrack

are deactivated.

•

If the mode is set for pressure and the

Oventrack

radio button is selected, the column

dimension fields are deactivated. In this case, the pressure is entered in the method and the

software maintains the column flow based on the initial oven temperature and pressure.

When the Oventrack mode is selected you cannot view the flow or velocity.

•

Capillary Control

is not selected, the split pneumatics only controls the inlet pressure

and split flow. The options in the field include None and Pressure. The Column Length and

ID fields, and Split Mode radio buttons are deactivated when capillary control is off.

The

Flow Offset

radio buttons are active with or without capillary control. The options include

Auto

, which is the default setting, and

Fixed

. When Auto is selected, enter the value for the

Leak Limit

. The Fixed option allows you to enter the split flow offset directly. The field label

changes from Leak Limit to

Offset

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды