PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 123

Страница: 123 / 284

FID Overview . 123

Touch

Stopwatch

icon from the Utilities screen.

Measure the flow rate. For best accuracy, use a soap bubble flowmeter volume that gives a reading

of at least 30 seconds.

NOTE: All gases exit through the top of the FID. If you use a flowmeter to measure the air and hydrogen gas

flows with a column connected to the FID and the carrier gas flowing, remember to subtract the carrier gas

flow from the total measured flow.

Repeatedly adjust the hydrogen flow and measure the flow until you obtain a flow rate of about 30

mL/min.

NOTE: Both the carrier gas and hydrogen gas exit through the FID. For satisfactory operation of the FID, a flow

rate of 30 mL/min of hydrogen is required. If a column is connected to the FID, and the carrier gas is set

and flowing, you should add the carrier gas flow rate to the required hydrogen flow. For example, if the

carrier gas flow is 30 mL/min, adjust the hydrogen flow until the measured total flow rate (combined carrier

gas and hydrogen) is about 60 mL/min (30 mL/min of hydrogen plus 30 mL/min of carrier gas).

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Бренды по названию

Популярные бренды