PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 166

Страница: 166 / 284

166 . Clarus 590 GC User’s Guide

Set the

Filter

200

The default setting is 200 msec. If you want to improve the signal-to-noise, change the setting to

800 msec. Then run your standard and observe that the signal remains the same and the noise

improves.

When all the settings are appropriate for your analysis touch

The FPD tab screen will be now visible and the changes you made in the configuration screen will

be shown.

Set the FPD Temperature

NOTE: The FPD temperature values must be entered between 250 °C and 450 °C only. Do not enter any value

less than 250 °C.

From the system status screen touch the

FPD

icon.

The FPD tab page is now visible.

NOTE: For proper ignition to occur, the FPD must be heated to at least 250 °C.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды