PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 204

Страница: 204 / 284

204 . Clarus 590 GC User’s Guide

If the Method Name field is empty, either from generating a New Method or from entry into the Method

Editor, the “Save As” dialog box appears.

Save As..

The Save As command saves the current method under a new or existing name.

Touching this option displays the Save As dialog box.

The Name field displays the name of the current method. The list of method names always

displays “External” in the last position.

If you do not change the name or select another method from the list, clicking

prompts the

dialog box to confirm that the existing method will be overwritten.

Clicking

Yes

overwrites the stored method with the new method with the same name.

To assign a new method name, touch the name field to invoke the alpha numeric keypad:

Although a new method name field displays the name “untitled,” the field to enter the new name

is blank.
The Method Name field displays each character as it is touched starting from the center of the

field. The name can be comprised of any combination of letters and numbers and is limited to 13

characters.

•

Touching

closes the keypad and displays the Save As dialog box with the name entered

in the name field.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Бренды по названию

Популярные бренды