PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 143

Страница: 143 / 284

PID Overview . 143

PID Overview

NOTE: The detector gas modules have been set to OFF at the factory.

The PerkinElmer Photoionization Detector (PID) is designed to allow the effluent from a chromatographic

column to be ionized by ultraviolet light (provided the ionization potential of the effluent is less than that of

the UV source). The current produced by the ion flow is measured by the detector and is proportional to

the concentration of the ionized material.
A cross section view of a PID is shown in the following figure.

NOTE: The optimum operating temperature for a photoionization detector is 250

C. PIDs may be operated at

350

C for short periods of time with a subsequent loss in lamp life.

The PID is equipped with a glass-lined inlet and exhaust that permits series operation with another

detector.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды