PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 98

Страница: 98 / 284

98 . Clarus 590 GC User’s Guide

Touch

The split flow will now turn off before the Clarus GC becomes ready so that at the time of injection

the split flow is off.

Touch

Add

The Add Timed Events screen appears.

From the Event drop down menu select

Split A

(if you have the injector configured for position A)

or Split B (if you have the injector configured for position B).

Touch the

Time

dialog box and use the up and down arrow or keypad

buttons to

enter a positive time for the event (for example, 2.00).

NOTE: The "Time" refers to the time (in minutes) into the GC run that you want to automatically turn the valve on.

The time depends on your sample, solvent, column, etc. Typical time values are between 0.25 and 2.0

minutes. An optimum "Time" is the time that provides maximum area counts (indicated by your data

handling device) with minimum solvent effect (tailing).

10.

Touch the

Value

dialog box and use the up and down arrow or keypad

buttons s to

enter a value of 50 mL/min.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды