PerkinElmer CLARUS 590 GC Скачать руководство пользователя страница 30

Страница: 30 / 284

30 . Clarus 590 GC User’s Guide

Injector and Detector Buttons

The screen is organized with Channel B devices above Channel A to reflect the position of the channels

on top of the GC. Injector and detector buttons display the active method settings for each device.

Touching a device icon displays the selected screen as well as a row of tabs to allow easy access to the

injector, oven, detector, and events for that channel. Touching the alternative channel icon on the top

navigation bar displays the active screen and associated tabs for the other channel if it is installed and

configured. The active method screens include navigation icons on the title bar that allow you to access

the same elements available from the Status screen.

Содержание CLARUS 590 GC





























































































































































































































































































Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды

PerkinElmer CLARUS 590 GC, Руководство пользователя

Результаты поиска

Содержание CLARUS 590 GC

Отзывы:

Похожие инструкции для CLARUS 590 GC

Бренды по названию

Популярные бренды