Nidek Medical RT-5100 Скачать руководство пользователя страница 217

Страница: 217 / 306

199

TEST METHOD

Convergence Test

Press [Break] when the chart appears dissociated.

The prism powers are stored as break point.

The [Break] indication is highlighted. It means that the prism powers have been entered.

When highlighted [Blur] is pressed again, the entered prism powers are cleared.

Turn the dial counterclockwise to reduce the BO prism powers from both eyes until the
chart appears one again.

Also possible by pressing

Press [Recov] when the chart appears one.

The prism powers are stored as recovery point.

161221687130 承認済

Uncontrolled copy when printed.

Содержание RT-5100



















































































































































































































































































































Результаты поиска

Содержание RT-5100

Отзывы:

Похожие инструкции для RT-5100

Бренды по названию

Популярные бренды

Nidek Medical RT-5100, Руководство оператора

Результаты поиска

Содержание RT-5100

Отзывы:

Похожие инструкции для RT-5100

Бренды по названию

Популярные бренды