Nidek Medical RT-5100 Скачать руководство пользователя страница 230

Страница: 230 / 306

• The rotary prism lenses are removed from the measuring windows when the already

selected button is pressed again in prism mode.

ex.When

is pressed in the base in/out prism, the rotary prism lenses are removed.

Appearance of

chart

Phoria

Correction

<1> The upper col-

umn is on the left.

Esophoria

Turn the dial clockwise to add the BO prism powers until
the two columns line up.

<2> The upper col-

umn is on the right

Exophoria

Turn the dial counterclockwise to add the BI prism
powers until the two columns line up.

212

21 Point Exams (only for Plus Package)

*Turning the dial changes the value in 0.5



increments for single eye.

*Use

instead of the dial for changing the prism value in 0.1



increments for sin-

gle eye.

161221687130 承認済

Uncontrolled copy when printed.

Содержание RT-5100



















































































































































































































































































































Результаты поиска

Содержание RT-5100

Отзывы:

Бренды по названию

Популярные бренды

Nidek Medical RT-5100, Руководство оператора

Результаты поиска

Содержание RT-5100

Отзывы:

Бренды по названию

Популярные бренды