Nidek Medical RT-5100 Скачать руководство пользователя страница 219

Страница: 219 / 306

201

TEST METHOD

Infravergence Test for Final Prescription (only for Plus Package)

4.8

Infravergence Test for Final Prescription

(only for Plus Package)

Use: Infravergence test for final prescription
Chart: Horizontal line
Auxiliary lens: Binocular rotary prism

Press [Final].

To perform this test, the final prescription must be entered beforehand.

To perform this test with a subjective value (#7 value), see "5.2.17 #12B Infravergence (Far),
#18B Infravergence (Near)" (page 232).

Press

to present the horizontal line chart. For the near point chart,

press

and set the near point horizontal chart manually.

The 10



BI dissociation prism is placed in the left measuring window.

The base up/down prism powers can be entered.

Press [Phoria] to display the Supraver-
gence test.

[Phoria] is displayed only when in FINAL
mode.

When [Phoria] indication is changed to
[Supravergence test], press [Supraver-
genece] to display the Infravergence test.

For the initial state, horizontal prism corre-
sponding to the horizontal phoria is set. If it
is not necessary, press

to clear the

data.

Turn the dial clockwise to add the BU prism powers to the single eye until the chart
appears dissociated.

Also possible by pressing

Press [Break] when the chart appears dissociated.

The prism powers are stored as break point.

The [Break] indication is highlighted. It means that the prism powers have been entered.

When highlight [Break] is pressed again, the entered prism powers are cleared.

Turn the dial counterclockwise to reduce the BU prism powers from the single eye until
the chart appears one again.

Also possible by pressing

Press [Recov] when the chart appears one.

The prism powers are stored as recover point.

The [Recov] indication is highlighted. It means that the prism powers have been entered.

161221687130 承認済

Uncontrolled copy when printed.

Содержание RT-5100



















































































































































































































































































































Результаты поиска

Содержание RT-5100

Отзывы:

Похожие инструкции для RT-5100

Бренды по названию

Популярные бренды

Nidek Medical RT-5100, Руководство оператора

Результаты поиска

Содержание RT-5100

Отзывы:

Похожие инструкции для RT-5100

Бренды по названию

Популярные бренды