Nidek Medical RT-5100 Скачать руководство пользователя страница 32

Страница: 32 / 306

BEFORE USE

Configuration

11-1.

Isolates a horizontal line (same visual acuity letters) on the top or bottom line of the VA chart.

•This key also moves the isolation up and down when the horizontal line has been isolated.

•



Isolates the horizontal line on the top line of the chart.

•



Isolates the horizontal line on the bottom line of the chart.

11-2. >

Isolates a vertical line on the VA chart.

•This key also moves the isolation to the left or right when the vertical line or single letter has been isolated.

•

+ >



Isolates a single letter in the lower-left or right corner on the chart.

11-3.

Isolates a single letter on the VA chart.
The letter in the upper-right corner of the chart is isolated.

•



Isolates the single letter in the upper-left corner of the chart.

11-4.

Isolate a horizontal line in the middle of the VA chart.

•



Applies the red-green filter on the VA chart.

again



Releases the red-green filter.

12. Pilot lamp

Lights up in blue while the RT-5100 is turned on.

13. Program keys

See “2.5 Standard Program Refraction” (page 43) for programmed refraction.

13-1.

Starts a program.
The elapsed time from program start is measured and displayed in the upper right field on the display when
the “Operating timer” parameter is set to “Prog.”

•Pressing this key again restarts the program.

•



Switches the program among A, B, C, D, E, and #7. (#7 is only for Plus Package)

13-2.

Used to forward next programmed refraction sequence.

•



Returns to the previous sequence.

161221687130 承認済

Uncontrolled copy when printed.

Содержание RT-5100



















































































































































































































































































































Результаты поиска

Содержание RT-5100

Отзывы:

Бренды по названию

Популярные бренды

Nidek Medical RT-5100, Руководство оператора

Результаты поиска

Содержание RT-5100

Отзывы:

Бренды по названию

Популярные бренды