Nidek Medical RT-5100 Скачать руководство пользователя страница 112

Страница: 112 / 306

OPERATING PROCEDURE

Printing



ON/OFF of printing of the Morgan’s criterion compared result

Whether or not to print the comparison result of the Morgan’s criterion can be set with the “Print Mor-
gan’s System” parameter.



The compared result with the criterion is not printed.

Yes



The compared result with the criterion is printed.



ON/OFF of printing of the Visual function analysis graph

Whether or not to print the visual function analysis graph can be set with the “Graph print” parameter.



The graph is not printed.

As - +13.00D



Graph between As to +13.00D is printed.

As - +3.00D



Graph between As to +3.00D is printed.

When the “Graph print”

parameter is set to
“As - +13.00D”

When the “Graph print”

parameter is set to
“As - +3.00D”

*AS: Accommodation stimulus

161221687130 承認済

Uncontrolled copy when printed.

Содержание RT-5100



















































































































































































































































































































Результаты поиска

Содержание RT-5100

Отзывы:

Похожие инструкции для RT-5100

Бренды по названию

Популярные бренды

Nidek Medical RT-5100, Руководство оператора

Результаты поиска

Содержание RT-5100

Отзывы:

Похожие инструкции для RT-5100

Бренды по названию

Популярные бренды