Nidek Medical RT-5100 Скачать руководство пользователя страница 282

Страница: 282 / 306

264

APPENDIX: Descriptions of Power Adjustment

D. Oblique Astigmatism

When the cylindrical axis is 16

to 74

or 106

to 164

D.1 First glasses

[Auto adjustment]

• The cylindrical powers are set to 0 for the patient who has slight astigmatism in both eyes (C: –0.25

D, –0.50 D).

• A certain power is reduced from each cylindrical power of –0.50 D or more. However, the difference

between the left and right eyes shall be within 0.75 D.

[Semi-auto adjustment]



Add –0.25 D to the cylindrical powers.

Adjustable within the full correction.



The cylindrical powers and axis are adjusted in the following order:

•

Reduce –0.25 D from the cylindrical powers.

•

Change the axis to either 90

or 180

(closer one).

•

Reduce certain powers from the cylindrical ones and change the axis.

* When the difference between the right and left cylindrical powers is large, the powers may be

changed up to –0.25 D only. This is because the patient eyes do not adjust to the glasses well with
0 D of monocular vision.

D.2 With glasses

When the LM data has been entered:

[Auto adjustment]

• A certain power is reduced from each cylindrical power.
• When the lensometry data is overcorrected, the full correction is selected.
• The difference between the left and right eyes shall be within 0.75 D. However, when the difference in

the LM data is large, the adjusted one may be over 0.75 D.

• The amount increased from the LM data shall be within 0.75 D. However, when the difference

between the left and right cylindrical powers in the LM data is large, the increased amount may be
over 0.75 D.

[Semi-auto adjustment]

Same as [Semi-auto adjustment] of D.1 First glasses.

161221687130 承認済

Uncontrolled copy when printed.

Содержание RT-5100



















































































































































































































































































































Результаты поиска

Содержание RT-5100

Отзывы:

Похожие инструкции для RT-5100

Бренды по названию

Популярные бренды

Nidek Medical RT-5100, Руководство оператора

Результаты поиска

Содержание RT-5100

Отзывы:

Похожие инструкции для RT-5100

Бренды по названию

Популярные бренды