Nidek Medical RT-5100 Скачать руководство пользователя страница 235

Страница: 235 / 306

217

21 Point Exams (only for Plus Package)

Turn the dial clockwise to add the BO prism powers to both eyes until the chart appears
dissociated.

*34

Also possible by pressing

Press [Break] when the chart appears dissociated.

The prism powers are stored as break point.

The [Break] indication is highlighted. It means that the prism powers have been entered.

When highlighted [Break] is pressed again, the entered prism powers are cleared.

Turn the dial counterclockwise to reduce the BO prism powers to both eyes until the
chart appears one.

*27

Also possible by pressing

Press [Recov] when the chart appears one.

The prism powers are stored as recovery point.

*34.

Turning the dial changes the value in 0.2



increments (0.1



for single eye). Turning the dial with pressing [Shift] changes

the value in 1.0



increments (0.5



for single eye).

161221687130 承認済

Uncontrolled copy when printed.

Содержание RT-5100



















































































































































































































































































































Результаты поиска

Содержание RT-5100

Отзывы:

Похожие инструкции для RT-5100

Бренды по названию

Популярные бренды

Nidek Medical RT-5100, Руководство оператора

Результаты поиска

Содержание RT-5100

Отзывы:

Похожие инструкции для RT-5100

Бренды по названию

Популярные бренды