manualshive.com logo in svg

Nidek Medical RT-5100, Руководство оператора

Поделиться
Скачать
Nidek Medical RT-5100 Скачать руководство пользователя страница 171

153

TEST METHOD

Visual Acuity Test

4

4.1.3

Visual Acuity Test with Addition Powers

The VA can be measured with addition powers when the addition powers are entered.

1 

Measure the addition powers.

See Steps 23 to 25 in Page 51.

2

Pull down the near point rod and set the near point chart.

Standard: Set either of the near point chart 1 (standard), 5: Letters chart, or 4: Landolt’s 
rings.

Plus Package: Set the near point chart II A: Letters chart or E: Landolt’s rings.

3

Press 

.

Check the near VA (see Step 26 in Page 
51).

4

Press 

 again.

The VA test with the addition powers starts 
and the VA display changes to A-VA.

When the addition powers are not entered, 
the test does not start.

Measure the near visual acuity.

5

Test the right, left, and binocular VA.

Press 

, 

 or 

 and turn the dial 

to enter each VA.

The VA cannot be entered with the mask 
keys such as 

 or 

.

When LM, AR, Subj, or Final mode is switched during ADD power VA measurement mode, 
the mode switches with the VA measurement mode in the ADD power. However, when the 
add power is not entered in the specified mode, the mode leaves VA measurement mode in 
the ADD power.

161221687130 承認済

Uncontrolled copy when printed.

Содержание RT-5100



















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды