Nidek Medical RT-5100 Скачать руководство пользователя страница 137

Страница: 137 / 306

119

ADVANCED FEATURES

Calling Up Data

3.12 Calling Up Data

3.12.1 Calling up measurement data

The RT-5100 stores the last 50

*23

measurement data. The data can be displayed.

Display the Recall Data screen.

1) Press

2) Press

Select the desired data.

Press the far left button of the desired
data.

The whole data is read.

When both day and night data are measured, the
day data and night data are saved together. When
night data exists with the day data,

appears

on the far left button. When the data is only the day
data,

appears on the far left button.

*23.When the Night data is saved together, the data that can be saved is less than 50 people.

As the Night data is counted as 1 data, when the Night data is saved together, it is counted as two people.

161221687130 承認済

Uncontrolled copy when printed.

Содержание RT-5100



















































































































































































































































































































Результаты поиска

Содержание RT-5100

Отзывы:

Похожие инструкции для RT-5100

Бренды по названию

Популярные бренды

Nidek Medical RT-5100, Руководство оператора

Результаты поиска

Содержание RT-5100

Отзывы:

Похожие инструкции для RT-5100

Бренды по названию

Популярные бренды