Nidek Medical RT-5100 Скачать руководство пользователя страница 269 | Manualshive

Страница: 269 / 306

Nidek Medical RT-5100 Скачать руководство пользователя страница 269

251

MAINTENANCE

Replacing Printer Paper

6

6.4

Replacing Printer Paper

When a red line appears on the side of the printer paper, it means that the paper is running short. In such
a case, stop using the paper and replace the roll with a new one.
The printer is installed in the system table (not included in the RT-5100 package) normally.

CAUTION

• Do not touch the auto cutter.

Printer head

Auto cutter

The auto cutter may hurt fingers.

• Do not touch the printer head.

The hot printer head immediately after printing
may cause a burn.
If the printer head is ruined or soiled, printing
quality may be reduced.

• Do not pull the printer paper with the paper cover closed.

Doing s o could ca us e ma lfunction of the printe r.

• When the printer paper gets jammed, remove the paper by the same procedure as when

replacing the printer paper, cut the crumpled paper, and then set the printer paper again.

1

Press the paper cover open button to open the paper

cover.

Paper cover open button

Paper cover

2

Remove the used printer paper.

161221687130 承認済

Uncontrolled copy when printed.

«
...
267
268
269
270
271
...
»

Содержание RT-5100



















































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды