![background image](http://html.mh-extra.com/html/nec/neax-2000/neax-2000_programming-manual_251364799.webp)
ND-91285-001(E)
DECEMBER, 1999
Page 17
Revision 1.0
(2/3)
ANNOUNCEMENT SERVICE (CONT’D)
OPERATING PROCEDURE(CONT’D)
To replay a message:
1. Go off-hook; receive Dial Tone.
2. Dial the DAT replay access code and DAT card number.
3. Receive a message.
4. Restore handset.
To delete a message:
1. Go off-hook; receive Dial Tone.
2. Dial the DAT delete access code and DAT card number.
3. Receive Service Set Tone.
4. Restore handset.
SERVICE CONDITIONS
1. A maximum of 5 different access codes can be assigned. There is a limit of 10 announcement cards for
each of the 5 different access codes. When recording an announcement, each announcement card must
be recorded individually.
2. This feature is supported by internal announcement circuits of MP card and an announcement card(s)
(2DAT/4DAT) installed in the system.
3. Either single or multiple connection to each announcement can be made on a system-programming
basis, and in the case of multiple connections the secondary station cannot be connected to the top of
the message.
4. Tie lines can access the ANNOUNCEMENT SERVICE.
5. Each time a station is connected to an announcement card, the message will be from 64 seconds.
The station will then be disconnected.
6. The duration of an announcement is limited to 64 seconds.
7. The system can be equipped with up to 128 DAT circuits for all announcement features. There are 2
circuits on MP card, 2 circuits on each 2DAT card, and 4 circuits on each 4DAT card.
8. ANNOUNCEMENT SERVICE can be used to provide a voice message when an incoming C.O. Line/
Tie Line call has been transferred by a station and encounter a busy or no answer condition. The busy
condition results in disconnect after three repetitions of the message.
a. Only 1 message of up to 64 seconds can be recorded on each individual voice recording memory
card.
b. In this application, a minimum of 2 circuits of DAT Cards are needed: one for a busy condition and
one for a no answer condition.
c. More than 1/circuit of DAT Card may be used, depending on traffic conditions.
d. CALL FORWARDING, if set, has priority over this feature.
e. DAT Cards can be shared among tenants. Each announcement is assigned on a per tenant basis.
f.
This feature does not function on Attendant transferred calls.
Содержание NEAX 2000
