![background image](http://html.mh-extra.com/html/nec/neax-2000/neax-2000_programming-manual_251364024.webp)
INTRODUCTION
HOW TO READ THIS MANUAL
– 4 –
A2001-10
HOW TO READ THIS MANUAL
Chapter 1 and Chapter 2 explains the feature programming for each service feature about the
following items.
PROGRAMMING
This section explains the programming procedure for each service feature.
The meaning of (1), (2) and marking are as follows.
(1)
: 1st data
(2)
: 2nd data
: Initial data; With the system data clear command (CM00, CM01), the data with this
marking is automatically set for each command.
:
A reset of the MP card is required after data setting.
Press SW1 switch on the MP card.
:
A reset of the AP00 card is required after data setting.
Set the Make Busy switch to UP and then DOWN.
:
A reset of the DTI card is required after data setting.
Set the Make Busy switch to UP and then DOWN.
:
Command with this marking can be used only under Off-Line mode of the
MP card.
:
Command with this marking can be used only under Off-Line mode of the
AP00 card.
HARDWARE REQUIRED
In this section, required hardware for each service feature is listed, except the following:
Single line telephone set and interface card (LC card)
Central Office Trunk card (COT card)
Attendant Console and interface card
INITIAL
AP00 INITIAL
DTI INITIAL
OFF LINE
AP OFF LINE
Содержание NEAX 2000
