E70 Series Instruction Manual
6.8 Optional Stop
II - 25
6.8 Optional Stop
(1) If M01 is programmed, the machine automatically stops by turning ON the OPTIONAL STOP switch. When the
switch is OFF, M01 is ignored and the machine does not stop.
(2) The machine stops after the M01 block is executed.
6.9 Optional Block Skip
When the OPTIONAL BLOCK SKIP switch is turned ON, a section of a block that follows a "/" (slash) is skipped; when
the switch is OFF, the block is executed. This enables the operator to specify whether or not a section of a block that
follows a "/" code is executed.
A block which has a "/" code in not the head but the middle is operated according to the parameter "#1226 aux10/bit1
(optional block skip type)" setting.
0: Enable only at the beginning of a block.
1: Enable in the middle of a block, as well as at the beginning of the block.
(Example)When machining two parts as illustrated below, if the following program is prepared and the machining is done
by turning ON the OPTIONAL BLOCK SKIP switch, part (a) is provided; if the machining is done by turning OFF the
switch, part (b) is provided:
Program
N1 G54 ;
N2 G90 G81 X50. Z-20. R3. F100 ;
/5 N3 X30. ;
N4 X10. ;
N5 G80 ;
M02;
Operation of a block which has a "/" in the middle, not at the head, depends on the setting of parameter "#1274 ext10/
bit4 (Optional block skip operation changeover)".
0: Follows the setting of "#1226 aux10/bit1".
1: Enable optional block skipping at the top and in the middle of a block.
Note that a slash "/" on the right-hand side of equation is handled as division operator.
Part (a)
Switch ON
N4
N4
N2
Part (b)
Switch OFF
N3
N2
Содержание E70 Series
