E70 Series Instruction Manual
Appendix 7.6 Data Input/Output-related Operation Messages
IV - 151
Message
Details
Merge complete
- The data merge completed.
Merge execution
- The data merge is being executed.
Memory alloc error
- Securing of the communication data range failed.
Rename complete
- The rename has been completed.
OK? (Y/N)
- Message to confirm the operation.
[Y] or [INPUT]: Execute the operation
[N]: Cancel the operation.
I/O not ready
- An error occurred between the NC and the external device.
I/O parameter error
- The external device settings and input/output parameters do notmatch.
I/O port busy
- Input/output was not possible as the I/O port is busy.
FD write protect
- The FD is write-protected.
Release the write protection.
PLC running
- An attempt was made to input a user PLC during PLC RUN.
- Stop the PLC on the maintenance screen.
FD not ready
- An attempt was made to perform an FD operation search with no FD.
- An attempt was made to display the FD list with no FD.
MemoryCard not ready
- An attempt was made to perform operations with no memory card.
DS not ready
- An attempt was made to perform operations with no data server.
USB memory not ready
- Operation was attempted when an USB memory is not inserted.
Can't write in READ-ONLY file
- Contact the service center.
Condense complete
- Condensing has been completed.
A directory does not exist
- The specified directory does not exist.
Setting complete normally
- Decryption code setting file of the system lock was set normally.
Guidance data loading
This will display only when the guidance data is loading from a memory card.
It will display when a memory card for guidance is inserted after the NC has
started and reading will take a few seconds to complete. (E70 only)
No guidance data in MemoryCard
Guidance data from memory card could not be read. Insert memory card with
guidance data before displaying guidance. (E70 only)
Содержание E70 Series
