E70 Series Instruction Manual
IV - 181
【
#8033
】
Fairing ON (for M system only)
Select whether to use the fairing function.
0: Not use
1: Use
Fairing function is enabled during G61.2 modal, regardless of this setting.
【
#8034
】
AccClamp ON (for M system only)
Select the method for clamping the cutting speed.
0: Clamp with parameter "#2002 clamp" or the corner deceleration function.
1: Clamp the cutting speed with acceleration judgment.
(Enabled when "#8033 Fairing ON" is set to "1".)
【
#8036
】
CordecJudge (for M system only)
Select the condition to decide a corner.
0: A corner is decided from the angle of the neighboring block.
1: A corner is decided from the angle of the neighboring block, excluding minute blocks.
(Enabled when "#8033 Fairing ON" is set to "1".)
【
#8037
】
CorJudgeL (for M system only)
Set the length of the block to be excluded when deciding a corner.
(Enabled when "#8036 CordecJudge" is set to "1".)
---Setting range---
0 to 99999.999 (mm)
【
#8041
】
C-rot.R
Set the length from the center of the normal line control axis to the tool tip. This is used to calculate
the turning speed at the block joint.
This is enabled during the normal line control type II.
---Setting range---
0.000 to 99999.999 (mm)
【
#8042
】
C-ins.R
Set the radius of the arc to be automatically inserted into the corner during normal line control.
This is enabled during the normal line control type I.
---Setting range---
0.000 to 99999.999 (mm)
【
#8043
】
Tool HDL FD OFS
Set the length from the tool holder to the tool tip.
---Setting range---
0.000 to 99999.999 (mm)
【
#8044
】
UNIT*10
Set the command increment scale.
The scale will be "1" when "0" is set.
---Setting range---
0 to 10000 (fold)
0: One fold
【
#8051
】
G71 THICK
Set the amount of cut-in by the rough cutting cycle (G71, G72)
---Setting range---
0 to 99999.999 (mm)
Содержание E70 Series
