6 Operation Panel Switch Functions
MITSUBISHI CNC
II - 30
Once the F1-digit feedrate is changed with manual handle, the changed feedrate is valid until parameter is changed or
the power is turned OFF. Changed feedrate can be checked only during the operation. Note that if the parameter "#1246
set18/bit16" (switch over of the F1-digit feedrate changing method) is set to "1", even after the power is turned OFF,
operation is kept at the changed feedrate because the parameter of F1-digit feedrate has been changed. In this case, if
the screen is not switched, the changed parameter values are not reflected to the display.
(Note 1) If F1-digit feedrate changing valid signal is turned ON when F1-digit feed is commanded and changing
feedrate with the manual handle is valid, it is clamped at the upper limit of F1-digit feedrate if the F1-digit
feedrate is greater than the upper limit of F1-digit feedrate.
(Note 2) When the F1-digit feedrate is 0 with the handle operation during the F1-digit feedrate command, the alarm
"M01 F1-digit feed rate zero 0104" will occur. This alarm can be eliminated when the F1-digit feedrate is set in
larger value than 0 with the handle operation.
(Note 3) When K is 0, the speed is not changed.
6.15.3 Preautions
(1) When G00 mode is applied, F1 to F5 are invalid in the G00 mode and the rapid traverse rate is established instead.
(2) If F0 is used in the G02, G03, G02.1 or G03.1 mode, a program error (P121) will occur. The error will be eliminated
if the F0 command is rewritten.
(3) When F1. to F5. (with decimal point) are assigned, the 1mm/min to 5mm/min (direct numerical value command) are
established instead of the F1-digit feed command.
(4) When the commands are used with inch command, one-tenth of the feedrate set correspond to F1 to F5 serves at
the assigned speed inch/min.
(5) When the commands are used with the millimeter or degree units, the feedrate set to correspond to F1 to F5 serves
as the assigned speed mm (°)/mm.
(6) Even if the F1-digit feed is commanded during feed per revolution (G95), it is executed as a normal F command
(direct numerical value command).
(7) When both the F1-digit feed command and inverse time feed command are present, the inverse time feed
command will have the priority.
(8) When both the F1-digit feedrate changing and the manual speed command are present, the manual speed
command will have the priority.
(9) In the synchronous tapping command, the speed cannot be changed with the handle.
Conversion of the F1-digit feedrate changing with handle operation
Содержание E70 Series
