6 Operation Panel Switch Functions
MITSUBISHI CNC
II - 44
6.20 Deceleration Check
6.20.1 Functions
The purpose of the deceleration check is to reduce the machine shock that occurs when the control axis feedrate is
suddenly changed, and prevent corner roundness. The check is carried out at block joints.
(1) Deceleration check during rapid traverse
The deceleration check is always carried out at the block joints (before executing the next block) during rapid
traverse.
(2) Deceleration check during cutting feed
The deceleration check is carried out at the block joints (before executing the next block) during cutting feed when
any one of the following conditions is valid.
(a)When the error detect switch is ON.
(b)When G09 (exact stop check) is commanded in the same block.
(c)When G61 (exact stop check mode) has been selected.
(3) Designating deceleration check
The deceleration check by designating a parameter includes "deceleration check specification type 1" and
"deceleration check specification type 2". The setting is selected with the parameter "#1306 InpsTyp".
(a) Deceleration check specification type 1 ("#1306 InpsTyp"= 0)
The G0 and G1 deceleration check method can be selected with the base specification parameter deceleration
check method 1 "#1193 inpos" and deceleration check method 2 "#1223 aux07/bit1".
(Note)
XX expresses all commands.
(b) Deceleration check specification type 2 ("#1306 InpsTyp"= 1)
Rapid traverse and cutting feed in-position are designated with the parameter "#1193 inpos".
(Note)
"G0" means the rapid traverse, and "G1" means the cutting feed.
Parameter
Rapid traverse command
Parameter
Other than rapid traverse command
(G1 : other than G0 command)
Inpos
(#1193)
G0
→
XX
(G0+G9
→
XX)
AUX07/BIT-1
(#1223/BIT-1)
G1+G9
→
XX
G1
→
XX
0
Command deceleration
check
0
Command deceleration
check
No deceleration check
1
In-position check
1
In-position check
Parameter
Command block
#1193 inpos
G0
G1+G9
G1
0
Command deceleration check
Command deceleration check
No deceleration check
1
In-position check
In-position check
No deceleration check
Содержание E70 Series
