Appendix 8 User Parameters
MITSUBISHI CNC
IV - 168
The parameters with "(PR)" requires the CNC to be turned OFF after the settings. Turn the power OFF and ON to enable
the parameter settings.
(Note) This parameter description is common for M700V/M70V/E70 Series.
It is written on the assumption that all option functions are added.
Confirm with the specifications issued by the machine tool builder before starting use.
【
#1025
】
l_plane Initial plane selection
Select the plane to be selected when the power is turned ON or reset.
1: X-Y plane (G17 command state)
2: Z-X plane (G18 command state)
3: Y-Z plane (G19 command state)
【
#1026
】
base_I Base axis I
Set the names of the base axes that compose the plane.
Set the axis name set in "#1013 axname".
If all three items ("base_I", "base_J" and "base_K") do not need to be set, such as for 2-axis
specifications, input "0", and the parameter will be blank.
Normally, when X, Y and Z are specified respectively for base_l, _J, _K, the following relation will be
established:
G17: X-Y
G18: Z-X
G19: Y-Z
Specify the desired axis name to set an axis address other than above.
---Setting range---
Axis names such as X, Y or Z
【
#1027
】
base_J Base axis J
Set the names of the base axes that compose the plane.
Set the axis name set in "#1013 axname".
If all three items ("base_I", "base_J" and "base_K") do not need to be set, such as for 2-axis
specifications, input "0", and the parameter will be blank.
Normally, when X, Y and Z are specified respectively for base_l, _J, _K, the following relation will be
established:
G17: X-Y
G18: Z-X
G19: Y-Z
Specify the desired axis name to set an axis address other than above.
---Setting range---
Axis names such as X, Y or Z
【
#1028
】
base_K Base axis K
Set the names of the base axes that compose the plane.
Set the axis name set in "#1013 axname".
If all three items ("base_I", "base_J" and "base_K") do not need to be set, such as for 2-axis
specifications, input "0", and the parameter will be blank.
Normally, when X, Y and Z are specified respectively for base_l, _J, _K, the following relation will be
established:
G17: X-Y
G18: Z-X
G19: Y-Z
Specify the desired axis name to set an axis address other than above.
---Setting range---
Axis names such as X, Y or Z
【
#1029
】
aux_I Flat axis I
Set the axis name when there is an axis parallel to "#1026 base_I".
---Setting range---
Axis names such as X, Y or Z
Содержание E70 Series
