
5 Diagnosis Screens
MITSUBISHI CNC
I - 322
Process Form
Set the sampling process type.
0:One-shot
The sampling stops when buffer is full.
1:Repeat valid
After the process ends (the buffer is full), the "Trigger wait" state will be
entered again.
2:Ring buffer valid
Sampling is executed as a ring buffer.
- If a value other than "0" is set, the "End condition" must also be set. If not,
the sampling process will not end until it is forcibly ended.
0 to 2
End condition
Select the condition for ending the sampling process. (Note 4)
0:Sampling completed
When the buffer is full, the sampling ends.
1:Variable No.
Sampling ends when the variable set in "variable No." is 0 or null (Note 2)
2:PLC device
Sampling ends at the falling edge of the signal set in "PLC device". (Note 3)
3:Address condition, true
Sampling ends when "address", "data" and "data mask" conditions are true.
(Note 1)
4:Address condition, false
Sampling ends when "address", "data" and "data mask" conditions are
false.
(Note 1)
0 to 4
Variable No.
This sets the variable No. that functions as the start/end trigger.If a number
that does not exist is input, an error will occur.
0:System variable (#1299)
Other than 0:Designated common variable(#100 or more, #500 or more)
- If both "Start condition" and "End condition" are set to other than "1"
(variable No.), the value will be ignored even if set.
0 to 999
PLC device
This sets the PLC device that functions as the start/end trigger. When "*" is
added at the head, the device will be a b contact.If a device that does not
exist is input or the device No. is not within the setting range, an error will
occur.
0:Data sampling trigger signal (Y72C)
Other than 0:Designated device
- If both "Start condition" and "End condition" are set to other than "2" (PLC
device), the value will be ignored even if set.
(*)X0000 to (*)X1FFF
(*)Y0000 to (*)Y1FFF
Address
This sets the address targeted for applying "Data mask". (Note 1) However,
if an illegal address (highest-order bit 0) is input, an error will occur.
- If both "Start condition" and "End condition" are set to other than "3" or "4"
(address conditions, true/false), the value will be ignored even if set. This
item can be set with the same methods as "address 1 to 8".
-
Data
This sets the data for judging the results of applying "Data mask" on
"Address".
- If both "Start condition" and "End condition" are set to other than "3" or "4"
(address conditions, true/false), the value will be ignored even if set.
-
Data mask
This sets the data mask to be applied on "Address".
- If both " Start condition " and " End condition" are set to other than "3" or
"4" (address conditions, true/false), the value will be ignored even if set.
-
Parameter
Details
Setting range (unit)
Содержание E70 Series
