![background image](http://html.mh-extra.com/html/mitsubishi-electric/e70-series/e70-series_instruction-manual_238514775.webp)
Appendix 8 User Parameters
MITSUBISHI CNC
IV - 242
【
#19005
】
manual Fcmd2 clamp
Set a clamp speed coefficient (%) for manual speed command 2.
The feed rate is clamped at the command feed rate or rapid traverse rate for automatic operation,
which was multiplied by this parameter's value.
(Note)This setting is valid only for manual speed command 2.
---Setting range---
0 to 1000 (%)
0: 100% (Default value)
【
#19006(PR)
】
EOR Disable
Set whether to handle an EOR(%) in machining program as the end of program in automatic
operation, graphic check, program transfer to NC memory, program editing, and buffer correction.
Tape operation, Computer Link B, and serial input/output are not included.
0: An EOR(%) is handled as the end of machining program.
1: An EOR(%) is not handled as the end of machining program. The program will be read to the
end of file.
【
#19008
】
PRM coord rot type
Select the start point of the initial travel command after parameter coordinate rotation.
0: Calculate the end position, assuming that the start point rotates in accordance with the
coordinates rotation.
1: Calculate the end position using the current position on the local coordinate system before
rotating, without rotating the start point in accordance with the coordinates rotation.
【
#19401
】
G33.n chamfer spd
Not used.
【
#19405
】
Rotary ax drawing
Specify this parameter to draw a path of C axis (rotary axis) according to its rotation in the graphic
trace and 2D graphic trace.
When "#1013 axname" is set to "C", the axis is handled as a rotary axis.
By setting this parameter to "C", a rotation path around the Z axis on actual workpiece can be
expressed.
When the Graphic check rotary axis drawing option or Graphic trace rotary axis drawing option is
disabled, this parameter is ignored.
C: Enable this function
0: Disable this function
(
Setting is cleared when "0" is set
)
【
#19406
】
Hob retract ON at alarm
Select whether to enable the retract at an alarm during hobbing.
0: Disable
1: Enable
【
#19407
】
Hob retract acceleration deceleration OFF
Select whether to disable the acceleration/deceleration of a retract.
0: Enable
1: Disable
【
#19417
】
Hole dec check 2
This is enabled when #1253 set25 bit2 is 1.
The operation at the hole bottom and the hole drilling stop position is as below.
0: Perform no deceleration check.
1: Perform command deceleration check.
2: Perform in-position check.
<Target fixed cycles>
Machining center: G81, G82, G83, G73
Lathe : G83, G87, G83.2
Содержание E70 Series
