4 Edit Screens
MITSUBISHI CNC
I - 232
(1) G code guidance may be refreshed when the cursor is located near the comment.
(2) When the cursor is located at the axis address, etc., the guidance for the nearest G code will be displayed even if
the address has no relationship with the G code.
(3) When moving the cursor to the block with no G code as follows, the contents of guidance will differ depending on
the cursor's route even if the cursor is in the same block.
(4) The instructions of G-code guidance are commonly used for M700V, M70V, and E70 series. Thus, G code could not
function though the guidance is displayed.
(5) Basically, G code format in the guidance is displayed using the format of 3-axis specifications of X, Y, and Z.
(6) Whichever plane is selected among the plane selection functions G17 to G19, the display data in the guidance is
displayed using X-Y plane (G17) format.
(7) When the G code command includes an address which have two or more meanings, both contents will be
displayed.
(8) G code guidance will not be refreshed while the character string is searched or replaced.
(9) G code guidance cannot be displayed in mass-editing.
(10) When the "UNIT NAME" of the H/W configuration screen is "FCU-MU558", NC loads the guidance data from a
memory card (CF card) at the timing of startup, but if the memory card (CF card) is inserted after the NC has
started, NC will load guidance data at the timing as follows.
(a) When operation, parameter, or alarm guidance is displayed.
(b) When switching display type to display G code guidance on edit screen.
(c) When G code guidance is displayed during display transition.
When NC is loading guidance data, "guidance data loading" message will show up, and loading will take few
seconds to complete.
(11) When the "UNIT NAME" of the H/W configuration is "FCU-MU558", once guidance data is loaded, guidance can be
shown even after the memory card (CF card) is removed.
Precautions for G code guidance
[Ex.]
The guidance for G01 will be displayed.
[Ex.]
G code that has a relationship with "X100. " is "G01", however, G code
guidance for "G90" will be displayed.
[Ex.]
When the cursor is moved by the route "a", the guidance for G01 which
is displayed last in N01 block will also be displayed in N02 block. When
the cursor is moved by the route "b", the guidance for G02 which is
displayed last in N03 block will also be displayed in N02 block.
( PROG01 ) ;
G01 G90 X100. ;
N01 G91 G01 X100. F1000 ;
↓
N02 Y100. Z100. ← ... a
↑ b
N03 G02 X50. Y50. R50. ;
;
Содержание E70 Series
