E70 Series Instruction Manual
IV - 169
【
#1030
】
aux_J Flat axis J
Set the axis name when there is an axis parallel to "#1027 base_J".
---Setting range---
Axis names such as X, Y or Z
【
#1031
】
aux_K Flat axis K
Set the axis name when there is an axis parallel to "#1028 base_K".
---Setting range---
Axis names such as X, Y or Z
【
#1037(PR)
】
cmdtyp Command type
Set the G code list and compensation type for programs.
1 : List1(for M) Type I (one compensation amount for one offset No.)
2 : List1(for M) Type II (shape and wear compensation amounts for one offset No.)
3 : List2(for L) Type III (shape and wear compensation amounts for one offset No.)
4 : List3(for L) Ditto
5 : List4(for special L) Ditto
6 : List5(for special L) Ditto
7 : List6(for special L) Ditto
8 : List7(for special L) Ditto
9 : List8(for M) M2 form at type Type I
(one compensation amount for one offset No.)
10 : List8(for M) M2 form at type Type II
(shape and wear compensation amounts for one offset No.)
There are some items in the specifications that can be used or cannot be used according to the
value set in this parameter.
The file structure may also change depending on the compensation data type.
(Note) When this parameter is changed, the file system will be changed after the power is turned
ON.
So always execute format.
The new format will be enabled after turning the power ON again.
Setting order
(1) cmdtyp changeover -> (2) Turn power ON again -> (3) Format -> (4) Turn power ON again
【
#1041(PR)
】
l_inch Initial state (inch)
Select the unit system for the program travel amount when the power is turned ON or reset and for
position display.
0: Metric system
1: Inch system
(Note) The units of the following data are converted by "#1041 I_inch".
- Command unit at power ON and reset (Inch/metric command mode)
But under the following conditions, the unit will follow G20/G21 command modal even at reset.
When reset modal is retained ("#1151 rstint"="0")
When G code group 06 reset modal is retained ("#1210 RstGmd/bit5" ON)
- Unit system for position display (counter, user parameter, tool, work offset)
- User parameter I/O unit
- Parameter unit of user parameters concerning length and speed
- Arc error parameter (#1084 RadErr)
【
#1063
】
mandog Manual dog-type
Select the manual reference position return method for the second return (after the coordinate
system is established) and later.
The initial reference position return after the power ON is performed with dog-type return, and the
coordinate system will be established.
(This setting is not required when the absolute position detection is used.)
0: High speed return
1: Dog-type
Содержание E70 Series
