Appendix 6 Explanation of Alarms
MITSUBISHI CNC
IV - 36
M01 Tap pitch/thread number error 0056
Details
The command for the pitch or the number of threads is not correct in the synchronous tapping
command of the multiple-spindle control II.
The pitch is too small for the spindle rotation speed.
Thread number is too large for the spindle rotation speed.
Remedy
- Correct the pitch, number of threads or rotation speed of the tapping spindle.
M01 Wait for tap retract 0057
Details
The axis travel command is interlocked in the part system where the "Tap retract possible" signal is
ON.
Remedy
- If tap retract is necessary, perform it before issuing an axis travel command. However, tapping
retract is not allowed during automatic operation. Carry out tapping retract after resetting.
- If tap retract is not necessary, cancel the tap retract enabled state.
M01 Handle ratio too large 0060
Details
- The handle ratio is too large for the handle feed clamp speed.
(The handle feed clamp speed changes according to the rapid traverse rate, external feedrate,
maximum speed outside the soft limit range and etc. (or external deceleration speed when external
deceleration is valid))
Remedy
- Change the settings of the handle feed clamp speed or the handle ratio.
M01 R-pos offset value illegal 0065
Details
At the start of reference position initial setting, "#2034 rfpofs (Distance-coded reference position
detection offset) is not set to "0".
Remedy
- Set "#2034 rfpofs" to "0", then turn the power ON again to perform the reference position initial
setting.
M01 R-pos scan distance exceeded 0066
Details
Reference position could not be established within the maximum scan distance.
Remedy
- Check the scale to see if it has dirt or damage.
- Check if the servo drive unit supports this function.
M01 Illegal op in wk instl err cmp 0070
Details
One of the following operations was attempted during workpiece installation error compensation.
- Manual interruption
- Automatic operation handle interruption
- MDI interruption
- PLC interruption
Remedy
- Return the operation mode to the original mode to remove the cause.
M01 No operation mode 0101
Details
No operation mode
Remedy
- Check for any broken wires in the input mode signal line.
- Check for any failure of the MODE SELECT switch.
- Correct the sequence program.
Содержание E70 Series
