E70 Series Instruction Manual
1.1 Maintenance Items
III - 3
(2) Other precautions for use
(a) Backlight
life
The life of the backlight is 50,000hours. (ambient temperature 25C°)
These are the time for luminance to drop to 50% of the initial value.
The backlight life is dependent on the temperature. The life tends to be shorter when used continuously at
lower temperatures.
(b) Luminance
start
Due to the characteristics of the backlight, the luminance could drop slightly at lower temperatures. It will take
approx.10 to 15 minutes for the luminance to reach the rated value after the power is turned ON.
(c) Unevenness,
luminescent spots and irregularities
Uneven brightness, small luminescent spots or small dark spots may appear on LCD panel, but this is not a
fault.
(3) Replacing the backlight
Replacement should be commissioned to the Mitsubishi Service Center.
1.1.3 Compact Flash/USB memory
(1) Handling the compact flash/USB memory
The general handling methods for the compact flash/USB memory are described below.
Refer to the instruction manual of the compact flash/USB memory used for details.
(a) Precautions for use
- Insert the card in the correct direction.
- Do not touch the connector area with hands or metal.
- Do not apply excessive force to the connector area.
- Do not subject the card to bending or strong impacts.
- Do not open the cover or disassemble the card.
- Do not use the card in dusty locations.
(b) Precautions for storage
- Do not store the card in locations having a high temperature or humidity.
- Do not store the card in dusty locations.
Содержание E70 Series
