E70 Series Instruction Manual
Appendix 6.12 Program Errors (P)
IV - 115
P48 Restart pos return incomplete
Details
A travel command was issued before the execution of the block that had been restart-searched.
Remedy
- Carry out program restart again.
Travel command cannot be executed before the execution of the block that has been restart-
searched.
P49 Invalid restart search
Details
- Restart search was attempted for the 3-dimensional circular interpolation.
- Restart search was attempted for the mixed control (cross axis control) command (G110).
- Restart search was attempted during the cylindrical interpolation, polar coordinate interpolation, or
tool tip center control.
- Restart search was attempted from a block (G68.2) during the inclined surface machining mode or
from the inclined surface machining mode cancel command block (G69).
- Restart search was attempted to the program after direct command mode.
Remedy
- Correct the program.
- Correct the restart search position.
P50 No spec: Inch/Metric change
Details
Inch/Metric changeover (G20/G21) command was issued while the function is out of specifications.
Remedy
- Check the specifications.
P60 Compensation length over
Details
The commanded movement distance is excessive (over 2
31
).
Remedy
- Correct the command range for the axis address.
P61 No spec: Unidirectional posit.
Details
Unidirectional positioning (G60) was commanded while the function is out of specifications.
Remedy
- Check the specifications.
P62 No F command
Details
- No feed rate command has been issued.
- There is no F command in the cylindrical interpolation or polar coordinate interpolation immediately
after the G95 mode is commanded.
Remedy
- The default movement modal command at power ON is G01. This causes the machine to move
without a G01 command if a movement command is issued in the program, and an alarm results.
Use an F command to specify the feed rate.
- Specify F with a thread lead command.
P63 No spec: High-speed machining
Details
High-speed machining cancel (G5P0) was commanded while the high-speed machining is out of
specifications.
Remedy
- Check the specifications.
Содержание E70 Series
