E70 Series Instruction Manual
IV - 175
【
#2010
】
fwd_g Feed forward gain
Set a feed forward gain for pre-interpolation acceleration/deceleration.
The larger the set value, the smaller the theoretical control error will be. However, if a machine
vibration occurs, set the smaller value.
---Setting range---
0 to 200 (%)
【
#2068
】
G0fwdg G00 feed forward gain
Set a feed forward gain for G00 pre-interpolation acceleration/deceleration.
The larger the setting value, the shorter the positioning time during in-position checking.
If a machine vibration occurs, set the smaller value.
---Setting range---
0 to 200 (%)
【
#2096
】
crncsp Minimum corner deceleration speed
Set the minimum clamp speed for corner deceleration in the high-accuracy control mode. Normally
set "0".
(Note) This parameter is invalid during SSS control.
---Setting range---
0 to 1000000 (mm/min)
【
#2109
】
Rapid (H-precision) Rapid traverse rate for high-accuracy control mode
Set the rapid traverse rate for each axis in the high-accuracy control mode. "#2001 rapid" will be
used when "0" is set.
---Setting range---
0 to 1000000 (mm/min)
【
#2110
】
Clamp (H-precision) Cutting feed clamp speed for high-accuracy control mode
Set the cutting feed maximum speed for each axis in the high-accuracy control mode. "#2002 clamp"
will be used when "0" is set.
---Setting range---
0 to 1000000 (mm/min)
【
#7914
】
ROT_PREFILT Rotary axis prefilter time constant
Set the time constant for rotary axis prefilter.
Setting this parameter can smoothen the tool angle change (rotary axis' motion) under tool center
point control.
When set to "0", "Rotary axis prefiltering" will be disabled.
---Setting range---
0 to 200 (ms)
【
#8001
】
WRK COUNT M
Set the M code for counting the number of the workpiece repeated machining.
The number of the M-codes set by this parameter is counted.
The No. will not be counted when set to "0".
---Setting range---
0 to 999
【
#8002
】
WRK COUNT
Set the initial value of the number of workpiece machining. The number of current workpiece
machining is displayed.
---Setting range---
0 to 999999
Содержание E70 Series
