6 Maintenance Screens
MITSUBISHI CNC
I - 386
Display item
Details
(3)
Setting by spindle area
Ch / Rotary SW No.
Set the servo I/F connection channel and the rotary switch No. (2-digit value) for each
spindle drive unit. This setting is registered at the "#3031 smcp_no".
1st digit: Servo I/F connection channel.
2nd digit: Rotary switch No.
Motor type
Set the motor types that are connected to each spindle. Input the values as indicated at the
guidance display area. The input values are not converted to motor types.
Power Supply type
Set the power supply types that are connected to each spindle drive unit.
Input the values as indicated at the guidance display area. The input values are then
converted to, and display as, power supply types.
If "0" is displayed, it means "No connection".
(4)
Setting by servo area
Ch / Rotary SW No.
Set the servo I/F connection channel and the rotary switch No. (2-digit value) for each servo
drive unit. This setting is registered at the "#1021 mcp_no".
1st digit: Servo I/F connection channel.
2nd digit: Rotary switch No.
Motor type
Set the motor types that are connected to each servo axis.
Input the values as indicated at the guidance display area. The input values are then
converted to, and displayed as, motor types.
Detector type
Set the encoder types that are connected to each servomotor.
Input the values as indicated at the guidance display area. The input values are then
converted to, and displayed as, encoder types.
Power Supply type
Set the power supply types that are connected to each servo drive unit.
Input the values as indicated at the guidance display area. The input values are then
converted to, and displayed as, power supply types.
If "0" is displayed, it means "No connection".
(5)
Guidance display area
Indicate the setting content and setting range for the setting item where the cursor is
positioned.
Menus
Menu
Details
Type
Reference
This writes the parameters based on settings on system setup screen to
NC system.
A
6.4.1 Writing Initial
Parameters
This displays the next page when guidance display content extends
through multiple pages.
C
This displays the 5th axis and following in setting by servo area when the
total number of axis in the part system exceeds 5.
C
Param
setting
Next
guide
Next
SV axis
Содержание E70 Series
